RadioMaster RP3 V2 ExpressLRS 2.4GHz Nano Receiver

19.99 $

PayPal
Visa
Master

Description

RadioMaster RP3 V2 Overview

Introducing the RadioMaster RP3 V2 ExpressLRS 2.4GHz Nano Diversity Receiver, a cutting-edge ISM device engineered to elevate your telemetry and signal reception capabilities to unprecedented levels. With an optimized PCB design, this receiver ensures superior heat dissipation, guaranteeing sustained performance even under demanding conditions.

Equipped with a Low Noise Amplifier (LNA), the RP3 extends the receiver range, capturing signals with enhanced sensitivity for seamless communication. Complementing this is a Power Amplifier (PA) that pushes telemetry range boundaries, empowering your system with extended reach and reliability.

Unmatched signal stability and range are achieved through Antenna Diversity technology, enabling seamless switching between antennas for optimal reception in any scenario. The inclusion of a temperature-compensated crystal oscillator (TCXO) further refines performance, maintaining precise frequency synchronization for consistent, reliable operation across varying conditions.

Operating within the 2.4GHz spectrum, the RP3 is compatible with all 2.4GHz ExpressLRS modules and transmitters, ensuring seamless integration with your existing setup. With telemetry RF power reaching a maximum of 100mW, you can harness the full potential of your telemetry system with confidence.

Featuring dual 65mm 2.4GHz T Antennas, the RP3 delivers comprehensive coverage across the frequency range of 2.404 – 2.479 GHz. Whether you’re pushing the limits with high refresh rates of up to 500Hz or ensuring reliable performance at a minimum of 25Hz, the RP3 stands ready to meet your demands.

Compact and lightweight at just 4.6g (including antennas), the RP3 is designed for efficiency without compromising on performance. Its compact dimensions of 22 x 13 x 4mm make it suitable for a wide range of applications, from FPV drones to remote-controlled vehicles.

Pre-installed with ExpressLRS v3.0 firmware and tailored for compatibility with the RadioMaster RP3 Diversity 2400 RX, the RP3 simplifies setup while providing the flexibility to adapt to your specific requirements. With a convenient CRSF bus interface, integration into your existing system is seamless, allowing you to focus on pushing boundaries without constraints. Experience the future of telemetry and signal reception with the RP3 Diversity Receiver.

 

Radiomaster rp3 v2 Radiomaster rp3. 2 - radiomaster rp3 v2 - motionew - 11 Radiomaster rp3. 3 - radiomaster rp3 v2 - motionew - 12 Radiomaster rp3. 4 - radiomaster rp3 v2 - motionew - 13 Radiomaster rp3. 5 - radiomaster rp3 v2 - motionew - 14 Radiomaster rp3. 6 - radiomaster rp3 v2 - motionew - 15 Radiomaster rp3. 7 - radiomaster rp3 v2 - motionew - 16

For a comprehensive reading of related products, please visit the Motionew website.

Additional information

Weight 0.5 kg
Dimensions 9 × 6 × 4 cm
Region

FCC, LBT

Specifications

Item
RP3 Diversity Receiver
Type ISM
MCU
ESP8285
RF Chip
SX1281
Antenna 65mm 2.4GHz T Antenna x2
Frequency Range 2.404 – 2.479 GHz
Maximum receive refresh rate 500Hz/F1000Hz
Minimum receiver refresh rate
25Hz
Telemetry RF Power 100mw
Working voltage 5V
Weight 4.6g (Including two antenna)
Dimension 22mm x 13mm x 4mm
Firmware Version ExpressLRS V3.0 pre-installed
FW Target RadioMaster RP3 Diversity 2400 RX
Bus interface CRSF

Product contents

Package Includes

 

Radiomaster rp3. 6 - radiomaster rp3 v2 - motionew - 17

Documents

Please contact us for more information.

Reviews

There are no reviews yet.

Be the first to review “RadioMaster RP3 V2 ExpressLRS 2.4GHz Nano Receiver”

Your email address will not be published. Required fields are marked *

fourteen − eleven =